Cudy POE40 2.0
Cudy POE40 2.0 (4-Channel Gigabit PoE++ Extender) متوفّر بالجملة عند Cudy Lebanon & Syria بلبنان وسوريا. إنجكتور و PoE. اطلب السعر والكمية عالواتساب.
A 4-channel PoE extender that splits one PoE connection into four for multiple clients and extends the PoE distance by up to 250m. (100m at 10/100/1000 Mbps, 250m at 10 Mbps)
- GbE In, 4× GbE Out
- 802.3bt/at/af Input
- 4× 802.3at/af Max 30W Output
- High-Speed Extension up to 100 meters
- Extend for 250 meters Transmission
- VLAN for Clients Isolation
- Watchdog On/Off
- Wall-Mount
المميزات
Power, Speed & Control in One
What is a PoE Extender? A PoE Extender allows you to extend both power and data over Ethernet beyond the standard 100 m (328 ft) limit. It receives PoE input from a PoE switch or injector and outputs power and data to the next device or another extender.Can I connect a PoE Extender directly to a non-PoE switch? No. A non-PoE switch does not provide power through Ethernet. You must use a PoE injector between the switch and the extender to supply power if you do not have a PoE switch.My PoE Extender is not working. What should I check first? Please verify the following:The upstream device (switch or injector) supports PoE or PoE+ (802.3af/at).Non-PoE switches cannot power the extender.The Ethernet cable is Cat5e or higher, in good condition, and under 100 m per segment.The total chain length (from the switch to the final device) does not exceed the maximum supported distance.The powered device (PD), such as a camera or AP, does not exceed the extender’s PoE output capacity.
FAQ
What is a PoE Extender? A PoE Extender allows you to extend both power and data over Ethernet beyond the standard 100 m (328 ft) limit. It receives PoE input from a PoE switch or injector and outputs power and data to the next device or another extender.Can I connect a PoE Extender directly to a non-PoE switch? No. A non-PoE switch does not provide power through Ethernet. You must use a PoE injector between the switch and the extender to supply power if you do not have a PoE switch.My PoE Extender is not working. What should I check first? Please verify the following:The upstream device (switch or injector) supports PoE or PoE+ (802.3af/at).Non-PoE switches cannot power the extender.The Ethernet cable is Cat5e or higher, in good condition, and under 100 m per segment.The total chain length (from the switch to the final device) does not exceed the maximum supported distance.The powered device (PD), such as a camera or AP, does not exceed the extender’s PoE output capacity.
المواصفات
| Model Version | |
| POE40 2.0 | |
| Protocols | |
| 802.3 Protocols | 802.3i 10 Mbps over Twisted Pair 802.3u 100 Mbps over Twisted Pair 802.3ab 1 Gbps over Twisted Pair 802.3x Flow Control 802.3af PoE 802.3at PoE 802.3bt PoE |
|---|---|
| PoE | |
| Uplink Stream | 1× GbE, 802.3bt/at/af |
| Uplink PIN Assignment | Mode A / Mode B / Four-Pair |
| Downlink Stream | 4× GbE, 802.3at/af |
| Downlink Pin Assignment | Mode A |
| Transimission Distance | Cat. 5e or higher cable: 100 meters at Gigabit Cat. 5e or higher cable: 250 meters at 10 Mbps Note: Distance from extender to switch depends on switch capability. Distance from extender to device follows extender rating |
| Transimission Distance Note | 250-meter transmission is only available under the Extend mode. |
| Buttons and LEDs | |
| Physical Buttons | VLAN/Default/Extend DIP Switch, Watchdog Switch |
| LED | Power |
| Power | |
| Power Input Type | PoE via Ethernet Port |
| Power Methods | 802.3at/af PoE 802.3bt PoE |
| Power Input | PoE IN: ≥60W is recommended |
| Max Power Consumption (W) | 2W |
| Max Power Output (W) | 2× 30W or 4× 12.95W |
| Note | The actual power output depends on input |
| Reliability | |
| Power Protection | Polarity Protection Overvoltage Protection Short-Circuit Protection Automatic Voltage Regulation |
| EMC | IEC/EN 61000-4-2, Level 3 ESD: Contact: 6kV; Air: 8kV IEC/EN 61000-4-5, Level 4 Surge: RJ45: CM 4kV |
| Environment | Ambient Operating Temperature: 0~40℃ (32~104 ℉) Storage Temperature: -40~70 ℃ (-40~158 ℉) Operating Humidity: 10%~95% non-condensing Storage Humidity: 5%~95% non-condensing |
| Certifications | |
| FCC, CE | |
| Mechanical | |
| Install in a Daisy Chain | Up to 3 extenders in a chain |
| Installation | Desktop Wall-mount |
| Dimension | 119×85×28 mm 4.69×3.35×1.1 inches |
| Casing Material | Metal |
| Product Weight | 254.5 g (8.98 oz.) |
| Package Content | |
| POE40 Mounting Kit Installation Guide | |
| Ordering Information | |
| Retail Package Dimension | 151×96×40 mm 5.94×3.78×1.57 inches |
| Retail Package Weight | EU: 372.4 g (13.14 oz.) |
| Units per Carton | 40 |
| Carton Net Weight | EU: 14.9 kg (32.85 lbs) |
| Carton Gross Weight | EU: 15.5 kg (34.17 lbs) |
| Carton Dimension | 44.1×32×21.7 cm 17.36×12.6×8.54 inches |